Type CFQ500 Automatic Wall Cement Plastering Machine

Basic Info

Model No.: CFQ500

Warranty Service: 1 Year

After-sales service: Online Technical Support, Free Spare Parts

place of origin: China

Power: 1.5kw

Voltage: 220v/380v

Efficiency: 500 square meter/8h

Plastering Way: Vibration Plastering

Vibrator: 3 Vibrators

Plastering Height: ≤5m

Plaster Width/time: 80cm

Plastering Thickness: 5-30mm

Perpendicularity Degree: Max 2mm

Lifting Speed: 3.6 M/30s

Additional Info

Packaging: Wooden box

Productivity: 100 sets per month

Brand: Borong

Transportation: Ocean

Place of Origin: HeBei of China

Supply Ability: 100 sets per month

Port: Tianjin

Product Description

Product description

The machine has the advantages of simple operation, beautiful appearance, stable operation, sturdy and durable, convenient movement, rapid positioning and no need for disassembly, which greatly improves the material utilization rate and engineering progress.

Our stucco wall machine can be completely wiped to the top without leaving a distance of one millimeter, and the yin and yang angles can be used in the proper position. At the same time, the positioning is fast, the positioning is very fast, and it can be flattened vertically in about 10 seconds. Combining the two departments and traditional management, the problem of slow laser positioning, difficult positioning and large error is solved. The use of a vibrator and the addition of a wiper solves the problem that the artificial applicator wall is prone to hollowing and cracking.

Plastering machine plastering technology

(First) Plastering works:

  In order to ensure the quality of the plastering project and avoid cracks, hollow drums, ash, etc., the following practices and measures are taken:

1. The mortar used in the plastering project should be stirred in strict accordance with the mix ratio.

2. The mix ratio and consistency of the plastering mortar should be used only after passing the inspection. Mortar mixed with cement or gypsum should be controlled to be used before initial setting.

3, in the construction in strict accordance with the normative standards to request and guide the construction: yin and yang angle to find the side, set the standard ribs, layering leveling, dressing, surface calendering.

4. Before the plastering, the brick wall must be watered and wetted in advance.

5. When admixture is used in the mortar, the amount of the admixture should be determined by experiment.

(Second) Plastering of the outer wall of the outer wall:

1. Grassroots cleaning:

Before the exterior wall is smeared with ash, the mortar, wood chips, loose crepe parts, etc. remaining on the surface of the base layer are cleaned and watered.

2. The outer wall reserved hole is filled:

(1) Firstly, the residual mortar, loose lumps, stones, etc. in the reserved hole are chiseled off, and the outer sides are chiseled into the outer eight bell mouths, and washed with water.

(2) Apply a cement slurry with a water-cement ratio of 0.4 to 0.5 in the vicinity of the wall of the cave.

(3) The two side molds fill the dry hard enthalpy of the proper amount of expansion agent and water repellent.

3. The external wall screw hole is filled:

(1) Both sides of the screw hole are chiseled into an outer bell mouth, and the sleeve inside is cut off.

(2) Fill the holes with a 1:2 dry hard cement mortar with an appropriate amount of expansion agent and water repellent plug.

(3) The round steel (outer water sealing tape) of the corresponding diameter is clamped into the PVC casing at both ends by about 5 cm.

(4) Seal the PVC casing shearing surface with waterproof material, and then fill the bell mouth with cement mortar (with appropriate amount of expansion agent and waterproof agent).

4. According to the design requirements, the 10×10 chute should be cut at the junction between the shear wall and the masonry, and the next step can be carried out after filling with the waterproof grease.

5, the outer wall window frame seam and surrounding practices:

(1) The gap between the door and window frame and the wall should be between 2.0 and 2.5 cm. After the frame is cleaned, the silicone caulking required by the design is used.

(2) The exterior window sill is high and low inside, and the inner window sill is 2cm higher than the outer window sill.

(4) Strengthen the inspection of the quality of the aluminum alloy window itself. All joints and screw legs should be coated with glass glue, carefully closed to remove any gaps that may cause water seepage.

Tech Parameter

As a professional machinery manufacturer, we do have different kinds of construction machinery. Thread Rolling Machine For Sale, contact me if you need it. We will offer you a reasonable Roll Thread Machine Price and best Thread Rolling Services. Besides this Z28-80, we do have Z28-200 Type Thread Rolling Machine, they are both High Speed Thread Rolling Machine. Also we have Steel Straightening Machine, Rebar Bending Hoop Machine, Hydraulic Concrete Converying Transport Pump, and so on. The most important, it can be customized according to various needs.